Coordinate - Revision history

EricChadwick: Updated.

2015-02-25T22:01:45Z

Updated.

Cheeseplus: 1 revision

2014-07-29T08:42:25Z

1 revision

BrandonPhoenix: added Coordinate page. Merged Cartesian, Positional, and Texture coordinates.

2010-08-12T20:34:02Z

added Coordinate page. Merged Cartesian, Positional, and Texture coordinates.

New page

__NOTOC__
{{:[[OutOfDate]]}}

= Coordinate =

== Cartesian ==

The most common way of describing and delineating 3D space. Space is delineated by three vectors at right angles to each other, labeled by longtime convention as X, Y, and Z, and starting at a center point called the Origin. This coordinate system is based on the ideas of Rene Descartes, aka Cartesius of the "Cognito ergo sum" fame (I think, therefore I am). It is a very efficient way to describe space, so most [[RT3D]] engines use this system.

== Positional ==

Coords for short, these are the numbers that tell the [[Engine|engine]] where to position things, whether in 3D or in 2D (like a [[Polygon|polygon]] or an [[Overlay|overlay]]). If positioning something in 3D, you need three coords, commonly called X, Y, and Z, and usually written as (X,Y,Z). If positioning something in 2D, you only use the X and the Y, and write it as (X,Y). For 2D, the X is horizontal, the Y is vertical, and the numbers usually start at (0,0) in the upper-left corner. But for 3D, Y is not always vertical.

== Texture ==

These are the numbers that tell the [[Engine|engine]] where to position [[Category:TextureTypes|textures]] on [[Mesh|mesh]]. The engine uses three texture coordinates, commonly called U, V, and W. U is the width of the texture, V is the height, and W is used for depth if you are using a 3D procedural texture.

The coordinates are measured in a scale of 0.0 to 1.0, with 0.0 and 1.0 at opposite sides of the texture. Numbers higher than 1.0 will make the texture tile, and negative numbers will mirror the texture.

With most 3D modeling software, these numbers are usually hidden from the artist, replaced by helpful visual representations of how the textures are projected. Planes, cylinders and spheres help the artist align the textures in a visual way, but it helps to know that engines see only the UVW numbers that these shapes create for the polygons.

Also called mapping coordinates.
----
[[Category:Glossary]]

@@ Line 1: / Line 1: @@
-__NOTOC__
+Coordinates are numbers that tell the game engine where to position things, whether in 3D or in 2D (like a [[Polygon|polygon]] or an [[Overlay|overlay]]).
-{{:[[OutOfDate]]}}
-= Coordinate =
+== Cartesian Coordinates ==
-== Cartesian ==
+Cartesian coordinates are the most common way of describing and delineating 3D space. Space is described by three vectors at right angles to each other, labeled by longtime convention as X, Y, and Z, and starting at a center point called the Origin.
-The most common way of describing and delineating 3D space. Space is delineated by three vectors at right angles to each other, labeled by longtime convention as X, Y, and Z, and starting at a center point called the Origin. This coordinate system is based on the ideas of Rene Descartes, aka Cartesius of the "Cognito ergo sum" fame (I think, therefore I am). It is a very efficient way to describe space, so most [[RT3D]] engines use this system.
+This coordinate system is based on the ideas of Rene Descartes, aka Cartesius of the "Cognito ergo sum" fame (I think, therefore I am).
-== Positional ==
+It is a very efficient way to describe space, so most game engines use this system.
-Coords for short, these are the numbers that tell the [[Engine|engine]] where to position things, whether in 3D or in 2D (like a [[Polygon|polygon]] or an [[Overlay|overlay]]). If positioning something in 3D, you need three coords, commonly called X, Y, and Z, and usually written as (X,Y,Z). If positioning something in 2D, you only use the X and the Y, and write it as (X,Y). For 2D, the X is horizontal, the Y is vertical, and the numbers usually start at (0,0) in the upper-left corner. But for 3D, Y is not always vertical.
+If positioning something in 3D, you need three coords, commonly called X, Y, and Z, and usually written as (X,Y,Z). If positioning something in 2D, you only use the X and the Y, and write it as (X,Y). For 2D, the X is horizontal, the Y is vertical, and the numbers usually start at (0,0) in the upper-left corner.
-== Texture ==
+=== Y-Up vs. Z-Up ===
-These are the numbers that tell the [[Engine|engine]] where to position [[Category:TextureTypes|textures]] on [[Mesh|mesh]]. The engine uses three texture coordinates, commonly called U, V, and W. U is the width of the texture, V is the height, and W is used for depth if you are using a 3D procedural texture.
+D applications can use different orientations for the Cartesian axes.
-The coordinates are measured in a scale of 0.0 to 1.0, with 0.0 and 1.0 at opposite sides of the texture. Numbers higher than 1.0 will make the texture tile, and negative numbers will mirror the texture.
+ds Max uses Z as the up coordinate because it started as a rendering tool for architects. Architectural projects commonly start with a flat plan view, where X and Y are width and length, and Z is the height above/below the ground.
 ----
 [[Category:Glossary]]

← Older revision	Revision as of 08:42, 29 July 2014
(No difference)